Stay connected

RollerDrive BT100

With a continuous power output of 11 watts, the BT100 is the entry product in the RollerDrive series and is suitable for conveyors with an hourly throughput of up to 600 containers (600 cycles). Its uncomplicated control facilitates integration into a variety of systems.
It requires no special controller with current limitation. With a service life of 6000 hours, it can convey up to 14 million containers using common zone lengths (700 mm). With a noise level of only 47 dB (A), the BT100 is the quietest drive roller. This is achieved by a one and two-speed, helical polymer planetary gear and a clutch. The construction of RollerDrive BT100 enables it to comply with DIN EN 60034 1:1998/A11: 2002 and is only classified as a minor nuisance.




RollerDrive BT100

Characteristics
  • 11 Watts mechanical performance
  • Integral overheat protection
  • 6 different gear ratios available
  • 6000 hours minimum operational time
  • Protection rate IP54 or IP66
  • 47 dB(A) mounted in a conveyor frame
  • 5 m cable length
  • Open cable termination or plug for use with Z-Card BT 24

User Manual Interroll RollerDrive BT100

BT100 Electrical Data
Nominal voltage 24 VDC
Voltage range 16-28 VDC
No load current 0.6 A
Maximum continuous current
 1.3 A
Maximum peak current 4.5 A
Maximum ripple from power supply 5 %
Mechanical Performance
 11 W
Noise emission (mounted) 47 dB(A) *
Lifetime under nominal conditions 6000 h
System Efficiency (Drive)
 36 %
* The value can vary according to installation conditions, profile shapes and the resonance behaviour of the system.

BT100 Speed/Load Performance Data

Gear Ratio Nominal Speed
m/s
 Nominal Torque (1.3 A)
Nm
 Peak Torque (4.5 A)
Nm
9 0.90
 0.45
 1.9
9R 0.70
 0.70
 2.6
21 0.40
 0.84
 3
30 0.30
 1.28
 4.4
37 0.20
 1.64
 6.6
37R 0.10
 2.50
 6.4

Minimum RL

 Cartridge  Tube Idler bearing Min RL
9:1 to 9:1 red. No groove 11 mm hexagonal end drilled and tapped M8 203
No groove 11 mm hexagonal spring loaded 246
No groove PolyVee end drilled and tapped M8 228
No groove PolyVee 11 mm hexagonal spring loaded 239
No groove Timing belt/3/8" chain end drilled and tapped 220
Groove 30 60 11 mm hexagonal end drilled and tapped M8 246
Groove 50 80 11 mm hexagonal spring loaded 262
21:1 to 37:1 red. No groove 11 mm hexagonal end drilled and tapped M8 221
No groove 11 mm hexagonal spring loaded 264
No groove PolyVee end drilled and tapped M8 246
No groove PolyVee 11 mm hexagonal spring loaded 257
No groove Timing belt/3/8" chain end drilled and tapped 238
Groove 30 60 11 mm hexagonal end drilled and tapped M8 264
Groove 50 80 11 mm hexagonal spring loaded 280
9:1 to 9:1 red. No groove 11 mm hexagonal end drilled and tapped M8 203
IP66 version Groove 30 60 11 mm hexagonal end drilled and tapped M8 246
21:1 to 37:1 red. No groove 11 mm hexagonal end drilled and tapped M8 218
IP66 version Groove 30 60 11 mm hexagonal end drilled and tapped M8 261
The minimum RL is determinate by the idler bearing and grooves. Maximum RL: 1500 mm.

DriveControl for BT100 RollerDrives
MultizoneControl Z-Card
top
© Interroll | Sitemap | Disclaimer